Flange Free Ball Float Steam Trap (CS41H)
|FOB Price:||US $30-60 / Piece|
|Min. Order:||10 Pieces|
|Min. Order||FOB Price|
|10 Pieces||US $30-60/ Piece|
|Production Capacity:||50000 PCS/Ye|
|Transport Package:||Wooden Case|
|Payment Terms:||L/C, T/T|
- Recommended Products
- 7 Products
- Product Image
- Product Name
- FOB Price
- Model NO.: CS41H
- Pressure: Low Pressure
- Connection: Flange
- Type: Ball Float
- Maxi Allowable Rate of Back Pressure: 80%
- Valve Seat: 2Cr13 / 304
- Exhaust Plant: Stainless Steel / Alloy
- Trademark: XIUTAI
- Origin: Wenzhou
- Certification: SGS, ISO, Ts
- Temperature: Low Temperature
- Material: Cast Iron
- Mini Working Pressure: 0.01MPa
- Valve Body, Cap: Wcb / 304
- Working Medium: Saturated Vapor, Condensed Water
- Size: Dn15-Dn150
- Specification: ANSI,
- HS Code: 8481804090
1. Able to Discharge Saturated Condensate
No water collects in the heating equipment, thus reaching higher heat exchange efficiency.
2. Not Affected by Steam Pressure Change
The float ball can automatically adjust the openness of valve seat hole and work continuously with stable performance.
3. Good Air Tightness
The stainless steel float ball is perfectly circular, highly precise and with good air tightness.
4. Good Ability to Exhaust Air
The elements in Y series can automatically exhaust non-condensing cold and hot gases, thus preventing air blocking and achieving good heating result.
5. Long Service Life
The entire surface of the float ball can be used as sealing surface and no concentrated wear will happen.
6. Small Supercooling Degree & High Rate of Allowable Back Pressure
7. Able to continuously drain condensate with steady flow. When used in condensate recovery system, it takes perfectly good effects.
By automation, speediness and continuing features, this valve is used for the steam heating equipment, condensation water recovery system and the place where needs removing condensation water at quick speed, and so stop steam leakage effectively and obtain optimum heating.
By the action of buoyancy, the position of floating ball changes with the water level of condensation water and adjust the opening of valve seat automatically, continue to discharge condensation water, when the condensation water stops, the floating ball fall onto bottom by gravity, then close opening of drain valve. The opening of drain valve is below the water lever, and so the water is separated from steam automatically, and form water seal without steam leakage.
|Mini Working Pressure||0.01Mpa||Maxi allowable temperature for cast steel||42 5|
|Mini degree of super cooling||0||Maxi allowable temperature for stainless steel||525|
|Leakage rate with loading||0||Working Medium||Saturated vapor, condensed water|
|Maxi allowable rate of back pressure||80%||Exhaust plant||Stainless steel / alloy|
|Valve body, cap||WCB / 304||Floating ball||Stainless steel|
|Valve seat||2Cr13 / 304||Filter||Stainless steel|
Condensation water loading (discharge)kg/h (select the multiplying power 2~3 times).
Maximum working pressure Mpa
Operation pressure differential
Valve material and nominal pressure
Connection mode and dimension
Use and Maintenance:
Confirm the valve material, pressure and check if the maximum is suitable for operation condition.
Before installation, clean the pipeline and clear away sundries.
The installation position shall be closed to heating equipment as much as possible.
Install the minimum point of pipe horizontally and the direction of flow should be the same to the label of valve.
Install steam trap for each heating equipment in case cause influence each other.
under the safe operation of system, open the valve in front of the steam trap, make it rise up to normal station slowly.
Do time-based maintenance for the normal working of steam trap.